  Setting Out - Obstructed Arcs
 On This Page...    Related Pages

## Introduction

Setting out an arc is an elegantly simple task, but every now and again, the origin point is not available for all sorts of reasons. This page looks at how arcs are set out in such situations.
Establishing an arc is one of the simplest tasks undertaken when setting out a project. The tape or some other measure is fixed at the origin point and swung around to scribe the arc, with reference pins knocked in every few metres, as warranted by the radius of the arc. Some inaccuracy may occur with large radii (15 metres or more) if the tape or measure sags, or if it is caught by the breeze, but generally speaking, it couldn't be much simpler....except, of course, when the origin is obstructed and inaccessible because it lies inside a building, behind a wall or in the middle of a tree!

Thankfully, there are a few 'tricks of the trade' that can be used when the origin point is inaccessible for whatever reason:

## Plot and Transfer

With this method, the arc is plotted out in a CAD system or on paper and a chord is drawn between the two tangent points (start or arc and end of arc). The chord is divided into a number of equal segments and the perpendicular offset from the chord to the arc is measured (or calculated) and recorded.

Out on site, the drawing is recreated by stretching a string line between the tangent points, measuring and marking the segments as determined in the office, and then measuring and marking the offsets. In the example shown opposite, the origin is obstructed by the wall at the rear boundary of the proposed pathway.

A chord (purple) is created between the two Tangent Points (TP) and equally sub-divided into 4 segments each of Y metres. The perpendicular distance (green) between to chord and the arc (orange) is measured at each of the segments and recorded as values a, b and c.

The whole arrangement can then be recreated on site.

## Calculate and Transfer

Again, this method uses chords subtended from the two tangent points, but this whole process can be carried out on site rather than in the office. The first chord is created by stretching a string line between the two tangent points. The mid point of the chord is established and marked and then the offset from the mid-point of the chord to the arc can be calculated using basic trigonometry.
An arc with a radius of 1800mm has its origin (R) obscured by a building. The arc links two tangent points labelled (A) and (B). A chord (AB) is created between the two tangent points and when measured is found to be 2950mm in length. The mid-point of the chord is determined and marked as (C). This creates a right-angled triangle ACR and it is known that AR=1800mm and AC= half of 2950mm = 1475mm. Using Pythagoras...

(AR²) = (AC²) + (RC²)

or

RC = SQRT (AR² - AC²)

therefore...

RC = SQRT(3240000 - 2175625)
= SQRT (1064375) = 1032mm Given that DR is a radius of the arc and therefore measures 1800mm, it can therefore be calculated that CD, the offset of the arc from the mid-point of chord AB is....
1800 - 1032mm = 768mm
...so, a perpendicular can be established from point C on the chord and point D established and marked with a line pin.
This simple procedure can be repeated again to determine further points on the arc, as follows....

A new fixed point on the arc has now been established at point D. A new chord can be created between A and D, and, when measured, this is found to be 1662mm in length.

The mid-point of this new chord can be determined by measuring from A (or D) and then labelled as (E). This creates a yet another right-angled triangle AER and it has already been noted that AR=1800mm and we can calculate that AE= half of 1662mm = 831mm. Using Pythagoras...

RE = SQRT (AR² - AE²)

therefore,

RE = SQRT(3240000 - 690561)
= SQRT (2549439) = 1597mm FR is a radius of the arc, ie, 1800mm, and so EF, the offset of the arc from the mid-point of chord AE is....
1800 -1597mm = 203mm
A new perpendicular can be created from point E on the chord and consequently point F is established and marked with a yet another line pin.

This procedure can be mirrored on the other side of the arc, that is, along a chord subtended from DB, and we then have the two tangent points plus 3 alignment points set out along the arc.

While these 5 reference points would be adequate to set out a relatively small radius arc such as this 1800mm example, for larger arcs more reference points could be needed to ensure accuracy. This can be done by repeating the above procedure, subtending new chords and establishing further points as many times as is required.

In this current example, the next chord would be subtended from AF to create point G and so on and so forth.    